Euro Pro 464XC, 464, 412N instruction manual

Automated PDF to Text preview page 4 to 6:

Accessories
Foot control
Brush

Blind hem
Adaptor 1.Fold the fabric as illustrated in figure (1) 2.Place the fabric under the foot. Turn the handwheel forwards until the needle sewings to the left.It should just picrce the fold of the fabric. If it doesn't , reposition the fabric under the foot.(2) 3.Sew slowly, guiding the fabric carefully 4.After sewing ,open the fold and press with an iron.
9 10

Buttonhole foot

Screwdriver

Button sewing plate

Needles (x2)

Spool pin Threader Bobbins (x2)

Zipper foot

Regular sewing foot

Twin needle

Fitting the snap-in sewing table
1.Keep the snap-in sewing table horizontal, and pull it out from the machine as photo(1) 2.The bobbin holder and accessory bag are put into the inside of the sewing table. 3.Pull the side cover to open it as photo (2) 2 1

3-step zig-zag
1.Sewing on lace and elastic,patching,mending, reinforcing edges. 2.Set machine as illustrated. 3.Place patch in position and sew around the edges. 4.When mending tears,it is advisable to use a piece of backing fabric to reinforce. 5.Fisrst sew over the center and then overlap on both sides. Depending on the type of fabric and damage, sew between 3 and 5 rows.
8

3

12

Buttonholes
Preparation 1.Raise the presser foot lever, remove the metallic presser foot, and replace on a buttonhole foot.(note: Before setting buttonhole foot, turn the handwheel and make sure that the feed dogs is below the needle plate and the needle have to be about 5MM above the needle plate.) 2.Make sure the diameter of the button and add 3mm(1/8") for the bartacks. 3.If you have a very thick button, add more to the diameter measurement. 4.Mark the position and length of the buttonhole on the fabric. 5.Position the fabric so that the needle is on the mark that is the furthest from you. 6.Pull the buttonhole foot towards you as far as it will go. 7.Lower the foot. a)Turn the pattern selector dial to .Sew at moderate speed until you reach the end mark. b)Turn the pattern selector dial to and sew 5-6 bartacks stitches. c)Turn the pattern selector dial to and sew the left side of the buttonhole to the mark that is further from you (beginning of buttonhole). d)Turn the pattern selector dial to and sew bartacks stitche
s. Remove the fabric from under the foot. Draw the upper thread through the backside of the fabric and knot upper and lower threads. Cut the center of the buttonhole with the seam ripper, being careful not to cut the stitches on either side. Tips: 1.Slightly reduce the upper thread tension to produce better results. 2.Use backing material for fine and stretchy fabrics. 3.It is advisable to use a gimp cord for stretch or knit fabrics.The zigzag should sew over the gimp. 4.Install buttonhole foot from back to front.
Pattern Sewing step

Connecting the machine to the power source
1.Connect plug "A" to the machine and plug "B" into the mains socket. 2.Turn on power switch "ON" 3.Connect the foot control `C' to the machine. 4.The speed of the machine can be regulated by applying pressure to the foot controller.

Sewing light

Press main switch "ON" for power and light on.

A C

B

Attaching the presser foot holder
1.Raise the presser foot clamp "a" (1) Attach the presser foot holder "b" as illustrated. Attaching the presser foot Lower the presser foot holder "a" until the cut-out "c" is directly above the pin"d"(2) Raise the lever, the presser foot `d' insert into the floor `c'. Lower the lever `e' ,the presser foot is fixed on the presser foot floor, and the presser foot "f" will engage automatically. Removing the presser foot Raise the presser foot. (3) Raise the lever "e" and the foot disengages. a 1 2 a e b d c f 3 e

11

4

Winding the bobbin
Place empty bobbin on winding spindle ,and place spool on the spool pin. Wind thread a few times by hand round the empty bobbin in a clockwise direction . press the foot control till the bobbin full. Remove the bobbin by cutting the thread with cutter.

Zigzag/Overlock stitching
1.There are 4 patterns of zigzag for selecting . Turn the pattern selector dial to the stitch trace you need(4 - 7).
Thread tension for zigzag stitch Back side

1

2 3 4

Right side

Inserting the bobbin
When inserting or removing bobbin, the needle must be fully raised. Open the hook cover: insert the bobbin in the bobbin case, so that the thread runs in a clockwise direction. Attention: Turn power switch to "off" position !

Zigzag foot Pattern selector dial

4

5

6

7

1.When turning the pattern selector dial, assure the needle tipis at the upper position, otherwise, it will be bent or damaged ,or fail to sewing 2.When selecting the pattern dial, set the position corectly, otherwise, it will hurt the needle ,or sew over the selected stitch trace. It will be different from the selected pattern.

Notice :

5

10