Panasonic TH-37PWD8 + TH-42PWD8 Series Service Manual & Repair Guide

Automated PDF to Text preview page 4 to 6:

TH-37PWD8BK

15.12. HB-Board (1 of 2) Schematic Diagram 15.13. HB-Board (2 of 2) Schematic Diagram 15.14. HX-Board Block Diagram 15.15. HX-Board Schematic Diagram 15.16. S1, V1 and V2-Board Block Diagram and Schematic Diagram 15.17. J-Board (1 of 2) and H3-Board Block Diagram 15.18. J-Board (2 of 2) Block Diagram 15.19. J-Board (1 of 4) Schematic Diagram (37 inch) 15.20. J-Board (2 of 4) Schematic Diagram (37 inch) 15.21. J-Board (3 of 4) Schematic Diagram (37 inch) 15.22. J-Board (4 of 4) Schematic Diagram (37 inch) 15.23. J-Board (1 of 4) Schematic Diagram (42 inch) 15.24. J-Board (2 of 4) Schematic Diagram (42 inch) 15.25. J-Board (3 of 4) Schematic Diagram (42 inch) 15.26. J-Board (4 of 4) Schematic Diagram (42 inch) 15.27. D-Board Block Diagram 15.28. D-Board (1 of 12) Schematic Diagram 15.29. D-Board (2 of 12) Schematic Diagram 15.30. D-Board (3 of 12) Schematic Diagram 15.31. D-Board (4 of 12) Schematic Diagram 15.32. D-Board (5 of 12) Schematic Diagram 15.33. D-Board (6 of 12) Schematic Diagram 15.34. D-Board (7
of 12) Schematic Diagram 15.35. D-Board (8 of 12) Schematic Diagram 15.36. D-Board (9 of 12) Schematic Diagram 15.37. D-Board (10 of 12) Schematic Diagram 15.38. D-Board (11 of 12) Schematic Diagram 15.39. D-Board (12 of 12) Schematic Diagram 15.40. C1 and C2-Board Block Diagram 15.41. C1-Board (1 of 2) Schematic Diagram (37 inch)

74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103

15.42. C1-Board (2 of 2) Schematic Diagram (37 inch) 15.43. C1-Board (1 of 2) Schematic Diagram (42 inch) 15.44. C1-Board (2 of 2) Schematic Diagram (42 inch) 15.45. C2-Board (1 of 2) Schematic Diagram (37 inch) 15.46. C2-Board (2 of 2) Schematic Diagram (37 inch) 15.47. C2-Board (1 of 2) Schematic Diagram (42 inch) 15.48. C2-Board (2 of 2) Schematic Diagram (42 inch) 15.49. SC-Board Block Diagram 15.50. SC-Board (1 of 2) Schematic Diagram 15.51. SC-Board (2 of 2) Schematic Diagram 15.52. SU-Board Block Diagram 15.53. SU-Board Schematic Diagram (37 inch) 15.54. SU-Board Schematic Diagram (42 inch) 15.55. SD-Board Block Diagram 15.56. SD-Board Schematic Diagram (37 inch) 15.57. SD-Board Schematic Diagram (42 inch) 15.58. SS-Board Block Diagram 15.59. SS-Board Schematic Diagram 16 Parts Location 16.1. Parts Location (1) 16.2. Parts Location (2) 17 Packing Exploded Views 17.1. Packing Exploded Views (1) 17.2. Packing Exploded Views (2) 17.3. Packing Exploded Views (3) 18 Mechanical Replacement Parts List 19 Rep
lacement Parts List 19.1. Replacement Parts List Notes 19.2. Electrical Replacement Parts List (37inch) 19.3. Electrical Replacement Parts List (42inch)

104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 123 123 124 125 125 126 127 128 131 131 132 153

4

TH-37PWD8BK

1 Applicable signals

5

TH-37PWD8BK

2 Safety Precautions
2.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

2.1.1.

Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MW and 5.2MW. When the exposed metal does not have a return path to the chassis, the reading must be .

Figure 1

2.1.2.

Leakage Current Hot Check (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5kW, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1. 3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

6