2006 Ford E-Series Passenger/Cargo (E150, E250, E250, E450) Workshop Repair & Service Manual (COMPLETE & INFORMATIVE for DIY REPAIR) ☆ ☆ ☆ ☆ ☆
* COMPLETE, Absolutely No Missing Pages!
* Official Service INFORMATION You Can Count On!
* Customer Satisfaction GUARANTEED!
This high QUALITY official manual for 2006 Ford E-Series Passenger/Cargo (E150, E250, E250, E450) is 100 percents COMPLETE and INTACT, no MISSING, CORRUPT pages, sections to freak you out! This manual is exactly as described. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices.
PAGES: 4,442 Pages
OS: Windows/Mac OS X/Linux/Android/iOS
2006 Ford E-Series Passenger/Cargo (E150, E250, E250, E450)
INSTANT DELIVERY: A download link will be sent to you instantly after payment. Simply click on the link and save it to your computer. You can use this Manual as long as you wish with no restrictions.
CUSTOMER SATISFACTION: If there is ANY kind of problem with the item you purchased, just drop a quick email. Within HOURS the issue shall be taken care of.
PRINTABLE MANUAL WITH DIAGRAMS: Just print the manual out and start to work. You can also use the manual with your Tablet/Laptop in your garage.
REFUND/EXCHANGE POLICY: We sell high QUALITY products only. However if you encounter any problems with the item you purchased, another replacement link will be sent to you. If were at fault, you will get 100 percents refund.
Buy ☆THE BEST MANUAL ON THE INTERNET☆ from responsible seller and get instant download now without uncertainty or surprise.
This highly detailed workshop service repair manual for download contains virtually everything you will ever need to repair, maintain, rebuild, refurbish or restore 2006 Ford E-Series Passenger/Cargo (E150, E250, E250, E450). All diagnostic and repair procedures and gives you access to the same information that professional technicians and mechanics have. You can view and print out the complete repair procedures with this workshop service repair manual Download - you do not need to be skilled with a computer.
1 2 A B C D
E F G H I J
K L M N O P
Q R S T U V
Table of Contents
1: General Information
00: Service Information
06: Brake System
11: Steering System
07: Automatic Transmission
09: Exhaust System
10: Fuel System
12: Climate Control System
13: Instrumentation and Warning Systems
14: Battery and Charging System
15: Audio Systems
18: Electrical Distribution
19: Electronic Feature Group
5: Body and Paint
02: Frame and Mounting
Front Disc Brake
The brake disc and hub is an integrally cast assembly.
The disc brake caliper:
· bolts to the front disc brake caliper anchor plate, which bolts to the front wheel spindle.
· is a guide pin slide, dual piston type.
The caliper housing has a fluid inlet at the center of the bore. A square section seal fitted into an annular
groove in the caliper bore seals against hydraulic pressure, while rubber boots seal the caliper pistons and caliper bore from contamination.
The pads are:
· contained within the front disc brake caliper anchor plate.
· held to the front disc brake caliper anchor plate abutments by brake disc anti-rattle clips.
Brake Caliper Anchor Plate
Removal and Installation
1. Remove the brake pads. For additional information, refer to Brake Pads in this section.
2. Remove the 2 brake caliper anchor plate bolts and the brake caliper anchor plate.
· To install (E-150), tighten to 175 Nm (129 lb-ft).
· To install (E-250, E-350, E-450), tighten to 225 Nm (166 lb-ft).
3. To install, reverse the removal procedure.
Rear Disc Brake
The rear brake disc has the following characteristics:
· A single piston rear disc brake caliper (E-150)
· A 2-piston rear disc brake caliper (E-250-450)
· A vented-cast, drum-in-hat type rear brake disc
· A rear disc brake caliper anchor that holds the brake pads
A rear wheel brake disc adapter that holds the rear disc brake caliper anchor and the rear wheel disc brake shield
Brake Disc and Hub
The brake disc and hub are made from a single casting and are not available separately. The brake disc and hub serve to mount the rear wheel bearings and the rear wheels. Brake disc and hub removal is part of the bearing, cups and seals repair procedure. For additional information, refer to Section 205-02B.
DESCRIPTION AND OPERATION Procedure revision date:
All vehicles come equipped with a Safety Compliance Certification Label. The location on the label marked TR is reserved for the transmission code. To determine the correct transmission for this vehicle, refer to the Ownerss Literature, Transmission Code Designations. All transmissions are equipped with an identification tag located on the transmission case. For model number, transmission part number, serial number and build date, refer to the transmission identification tag located on the transmission case.