Complete workshop & service manual with electrical wiring diagrams for Mitsubishi Magna, Ralliart Magna, Verada, Verada Diamante, Sigma, V3000. Its the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Mitsubishi Magna, Ralliart Magna, Verada, Verada Diamante, Sigma, V3000 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

MAKE: Mitsubishi
YEAR: 1991 1992 1993 1994 1995
MODEL: Magna (TR-TS Series), Verada (KR-KS Series), Sigma, V3000

MAKE: Mitsubishi
YEAR: 1998 1999 2000 2001 2002
MODEL: Magna (98-01 TH, 03 TL, 98-02 TJ), Verada Diamante (98-01 KH, 03 KL, 98-02 KJ), Ralliart Magna (00-02 TJ)

MAKE: Mitsubishi
YEAR: 1998 1999 2000 2001 2002
MODEL:
98-01 Magna TH [incl. AWD models], 98-02 Magna TJ [incl. AWD models]
98-01 Verada Diamante KH [incl. AWD models], 98-02 Verada Diamante KJ [incl. AWD models]
00-02 Ralliart Magna TJ [incl. AWD models]

EXCERPT:
GROUP INDEX
General . . . . 00
Engine . . . . . 11A
Engine Overhaul . . . . . 11B
Lubrication . . . . 12
Multipoint Fuel Injection . . . . 13A
Fuel Supply . . . 13F
Traction Control System . . . 13H
Engine Cooling . . . 14
Intake and Exhaust . . . . . 15
Engine Electrical . . . . 16
Engine and Emission Control . . 17
Clutch . . . . . 21
Manual Transmission . . . 22
Automatic Transmission . . . 23
Front Axle . . . . . 26
Rear Axle . . . . . 27
Wheel and Tyre . . . 31
Power Plant Mount . . . 32
Front Suspension . . . . 33
Rear Suspension . . . . 34
Service Brakes . . . 35
Parking Brakes . . . 36
Steering . . . . 37
Body . . . . 42
Exterior . . . . 51
Interior . . . . . 52A
Supplemental
Restraint System (SRS) . . . . 52B
Chassis Electrical . . . 54
Heater, Air Conditioning and
Ventilation . . . . 55

INHIBITOR SWITCH AND CONTROL CABLE ADJUSTMENT
1. Set the selector lever to the N position.
2. Loosen the control cable to manual control lever coupling nut to free the cable and lever.
3. Set the manual control lever to the neutral position.
4. Loosen the inhibitor switch body mounting bolts and turn the inhibitor switch body so the hole in the end of the manual control lever and the hole (cross section A-A in the figure on the left) in the flange of the inhibitor switch body flange are aligned.
5. Tighten the inhibitor switch body mounting bolts to the specified torque. Be careful at this time that the position of the switch body is not changed.
6. Gently pull the transmission control cable in the direction of the arrow, and then tighten the adjusting nut.
7. Check that the selector lever is in the N position.
8. Check that each range on the transmission side operates and functions correctly for each position of the selector lever.