This is the Highly Detailed factory service repair manual for the Linde Electric ForkLift Truck Type 337-02 (LDC): E35, E40, E48, This Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic. The manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.




Model Covers:

E35
E40
E48



Service Repair Manual Covers:

4.6 INTRODUCTION
4.6.1 PRINCIPLE OF THE FIELD EFFECT TRANSISTOR
4.6.1.1 CONTROL OF FIELD-EFFECT TRANSISTORS
4.6.1.2 TRANSISTOR MODULE TERMINALS
4.6.1.3 INSTALLATION OF THE TRANSISTOR MODULES
4.6.1.4 COMPACT POWER MODULES
4.6.1.5 TRACTION AND LIFT POWER MODULE
4.6.1.6 POWER MODULE TESTS (Traction module illustrated)
4.6.1.7 TEST CONDITIONS
4.6.1.8 TESTING IF POWER MODULE IS OFF
4.6.1.9 TESTING IF THE POWER MODULE IS ON
4.6.1.10 TESTING THE PROTECTIVE DIODE IN THE POWER MODULE
4.6.1.11 TESTING THE FREEWHEEL AND BRAKE DIODES IN THE POWER MODULE
4.6.1.12 TESTING THE REGENERATIVE CURRENT DIODE IN THE POWER MODULE.
4.6.1.13 INSTALLATION OF THE TRANSISTOR MODULES
4.6.2 TRACTION CIRCUIT
4.6.2.1 TRACTION CIRCUIT - FORWARD DIRECTION
4.6.2.2 TRACTION CIRCUIT - REVERSE DIRECTION
4.6.2.3 TRACTION CIRCUIT - FREEWHEEL
4.6.2.4 TRACTION CIRCUIT - REGENERATIVE BRAKING (STAGE 1)
4.6.2.5 TRACTION CIRCUIT - REGENERATIVE BRAKING (STAGE 2)
4.6.3 DIRECTION CONTACTOR
4.6.3.1 DIRECTION CONTACTOR - TIP REPLACEMENT
4.6.4 REGEN CONTACTOR
4.6.5 ELECTRONIC TRACTION CONTROL UNIT 1A1
4.6.5.1 OPTIONAL OUTPUT
4.6.5.2 SWITCH CONTROLLED SPEED RESTRICTION
4.6.5.3 TRACTION CONTROL MODULE CONNECTOR PIN DESIGNATIONS
4.6.5.4 TRACTION MODULE POWER SUPPLY
4.6.5.5 NEGATIVE TRACTION ENABLE
4.6.6 24 VOLT ELECTRONIC VOLTAGE REGULATOR
4.6.7 ALARM OPTION
4.6.7.1 OPERATION OF AUDIBLE ALARM (OPTION)
4.6.8 HANDBRAKE INTERLOCK.
4.6.9 TRACTION MOTOR TEMPERATURE INTERLOCKS AND WARNINGS
4.6.10 ACCELERATOR OPERATION
4.6.10.1 ACCELERATOR UNIT
4.6.10.2 SINGLE PEDAL OPERATION.
4.6.10.3 FORKS FORWARD DIRECTION SELECTED
4.6.10.4 FORKS TRAILING DIRECTION SELECTED
4.6.10.5 CHECKING OPERATION OF THE ACCELERATOR UNIT
4.6.11 CURRENT SENSOR
4.6.11.1 CURRENT SENSOR DESCRIPTION
4.6.11.2 CURRENT SENSOR OPERATION
4.6.11.3 FORMULA FOR CURRENT SENSOR CHECK
4.6.12 OPERATION AND SETUP OFF SPEED SENSOR (1B8)
4.6.12.1 TRACTION SPEED & DIRECTION SENSOR 1B8
4.6.12.2 CHECKING SENSOR WITHOUT LAPTOP OR LINDE TEST ADAPTOR
4.6.13 FIELD DIVERT
4.6.13.1 DIVERT REQUIREMENTS
4.6.13.2 FIELD DIVERT CONTACTOR PART
4.6.14 HYDRAULIC PULSE LTM
4.6.14.1 ELECTRONIC LIFT CONTROL
4.6.14.2 HYDRAULIC MODULE REMOVAL
4.6.14.3 HYDRAULIC MODULE REPLACEMENT
4.6.14.4 HYDRAULIC THERMAL SWITCH 2B11
4.6.14.5 HYDRAULIC MODULE PIN DESIGNATION
4.6.14.6 MODULE VOLTAGES TO AND FROM HYDRAULIC CONTROL POTENTIOMETER 2B1
4.6.14.7 HYDRAULIC CONTROL MODULE ADJUSTMENTS
4.6.15 BATTERY DISCHARGE INDICATOR & USE OF THE SERVICE TOOL
4.6.15.1 REPROGRAMMING THE COMBINATION INSTRUMENT WITH THE DIAGNOSIS UNIT
4.6.15.2 DIAGNOSTIC MODULE
4.6.15.3 COMBINED BATTERY DISCHARGE INDICATOR, HOUR METER, BRUSH WEAR, BRAKE FLUID LEVEL, MOTOR OVER-TEMPERATURE INDICATOR AND VEHICLE STATUS INDICATOR.
4.6.16 POWER STEERING
4.6.16.1 POWER STEERING CONTROL
4.6.16.2 POWER STEERING CONTROL
4.6.17 BRAKE WEAR INDICATOR 6A1 (OPTIONAL)
4.6.18 EARTH FAULTS
4.6.18.1 FITTING AUXILIARY ELECTRICAL EQUIPMENT
4.6.18.2 CABLE RUNS
4.6.18.3 INTERMITTENT FAULTS
4.6.18.4 CABLES
4.6.18.5 CABLES - INSPECTION
4.6.18.6 FAULT ANALYSIS
4.6.19 LIGHTING AND AUXILIARY 12 VOLT CIRCUITS CIRCUIT DIAGRAM
4.6.20 TRUCK DIAGNOSTICS
4.6.20.1 DIAGNOSIS WITH THE LINDE DIAGNOSIS MODULE
4.6.20.2 LINDE INTERFACE CONVERTER
4.6.20.3 INSTALLATION OF THE DIAGNOSIS SOFTWARE TEST & SETUP
4.6.20.4 FIRST TIME INSTALLATION INSTRUCTIONS
4.6.20.4.1 UPDATE INSTALLATION INSTRUCTIONS
4.6.20.5 STARTING AND SELECTING LINDE PROGRAM
4.6.20.6 STARTING THE DIAGNOSIS PROGRAM TEST & SETUP
4.6.20.7 LINDE DIAGNOSIS PROGRAM
4.6.20.8 HELP FUNCTION
4.6.20.9 TRACTION DIAGNOSTICS
4.6.20.10 INDEX TO TRACTION DIAGNOSTIC WINDOWS
4.6.20.11 INTERFACE:
4.6.20.12 INTERFACE CONVERTER STATUS:
4.6.21 WINDOWS
4.6.21.1 WINDOW 1 STATUS INFORMATION.
4.6.21.2 WINDOW 2 TEST DATA AND FAULT DIAGNOSIS
4.6.21.3 WINDOWS 3 AND 31 STORED FAULT DIAGNOSIS
4.6.21.3.1 WINDOW 32 DELETION OF STORED FAULT DIAGNOSIS (MASTER VERSION ONLY)
4.6.21.4 WINDOW 4 SWITCHING POSITION OF MICROSWITCHES
4.6.21.4.1 WINDOW 41 ADDITIONAL CONTROL SIGNALS (MASTER VERSION ONLY)
4.6.21.6 WINDOW 6 ANALOGUE CONTROL SIGNALS
4.6.21.6.1 WINDOW 61 INTERNAL CONTROL SIGNALS (MASTER VERSION ONLY)
4.6.21.6.2 WINDOW 62 INTERNAL CONTROL SIGNALS (MASTER VERSION ONLY)
4.6.21.7 WINDOW 7 ADJUSTING TRUCK PARAMETERS
4.6.21.7.1 WINDOW 71 SETTING TRUCK PARAMETERS FROM WINDOW 7 TO DEFAULT SETTINGS
4.6.21.7.2 WINDOW 72 DISPLAY OF PARAMETERS FROM SPECIAL VERSION
4.6.21.7.3 WINDOW 73 TRACTION DEFAULTS (SETS ADJUSTMENT IN PAGE 7 TO DEFAULT VALUES) (MASTER VERSION ONLY)
4.6.21.7.4 WINDOW 74 UPA PARAMETERS ONLY
And More......



========================================
File Format: PDF, 93 pages
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader & WinZip





NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are https://www.tradebit.com is great to have Linde Electric ForkLift Truck Type 337-02 (LDC): E35, E40, E48 Service Repair Workshop Manual.




Thanks for visiting!