26.94 GBP

Download Now
Sold by tbit on Tradebit
The world's largest download marketplace
3,111,188 satisfied buyers
Shopper Award

#❶ Linde Forklift Truck H-Series Type 394: H40D, H40T, H45D, H45T, H50D, H50T Service Training (Workshop) Manual pdf

Linde Forklift Truck H-Series Type 394: H40D, H40T, H45D, H45T, H50D, H50T Service Training (Workshop) Manual pdf

Original Illustrated Factory Service Training (Workshop) Manual for Linde Forklift Truck H-Series Type 394.

Original factory manuals for Linde Forklift Trucks, contains high quality images, circuit diagrams and instructions to help you to operate and repair your truck

Covered models:

Format: ZIP, including:
Service Training Manual, PDF, 606 Pages
Diesel Trucks Circuit Diagrams, PDF, 204 Pages
LPG Trucks Circuit Diagrams, PDF, 225 Pages

Language: English

0. Product information
394 truck series
Truck 394
Truck 394 MPR
LHC basic structure
1. Engine
LPG engine
Description of the drive
BMFVR6 technical data
Engine block
V-ribbed belt removal and installation
Checking the compression pressure
Cylinder head removal and installation
Checking and adjusting the timing
Removing and refitting the cylinder head cover
Installing and removing camshafts
Engine cooling system
Coolant -draining and filling
Coolant regulator housing assembly and disassembly
Engine electrics
Three-phase alternator
Electronic ignition system overview
LPG system
Safety guidelines for LPG (extract)
Basic rules when working with LPG
Sealing plastic pipe unions
LPG system -functions
Shut-down due to lack of gas
Evaporator -functions
Mixer -functions
Default settings for the LPG system
Speed control (from chassis number H2X394U04459 onwards)
LPG shut-off valve
LPG truck with a lambda control system
Exhaust gases -composition
Lambda control system
Leakage test on LPG system
Removing and installing the level display and 80 filling stop valve
The following safety measures must be observed
Carrying out assembly operations
Bleeding the LPG tank
The following safety measures must be observed
Procedure for bleeding
BJCdiesel engine
Description of the drive
BJC technical data
Particularities of the 1.9-litre engine
The electronic engine control unit
Coolant temperature sending unit 0B1
Engine speed sensor 0B2
Actual speed sensor 1B1
Fuel temperature sending unit 0B3
Sensor 0B4
Needle stroke sensor 0B5
Height sensor
0B3 control gate valve travel sensor
Glow plug system
Pre-heater system
Glow plugs- engine 0R1
Fuel supply
Fuel quantity regulation
Fuel quantity actuator 0B3
Fuel shut-offvalve 0Y1
Injection timing device- replacement of O-ring on cover
Start of injectionvalve 0Y2
Start of injection -governing
Start of injection -dynamic check and adjustment
Injection nozzle -Two-spring nozzle holder
Injection nozzles- removal and installation
One-way restrictor
Injection system - overview
Injection system -supply voltage check
Injection pump - removal and refitting, Exchanging the toothed belt
Injection pump - removal and installation
Injection pump - pump and toothed belt adjustment
Engine block
Ribbed V-belt- removal and fitting
Crankshaft oil seal on pulley end -removal and installation
Crankshaft sealing flange- removal and installation
Checking the cylinder head
Cylinder head - removal and fitting
Cylinder head - compression check
Valve gear
Oil pressure and oil pressure switch -check
Oil sump - removal and installation
Checking hydraulic bucket tappets
Camshaft- removal and installation
Vacuum pump
Air volumeter 0B6
Solenoid valve for boost pressure limitation 0Y4
Charge air system with exhaust turbocharger
Coolant -draining and filling
Coolant thermostat- removal and installation
Water pump -removal and installation
Coolant pump -Checking for wear
Engine electrics
Three-phase alternator
Replacing the engine control unit/ immobilizer
Self-test- introduction
Self-diagnostics -troubleshooting
Standardised measured value blocks
Measured value block 01 -evaluation
Measured value block 04 -evaluation
Measured value block 05 -evaluation
Measured value block 07 -evaluation
Measured value block 10 -evaluation
Measured value block 11 -evaluation
Measured value block 12 -evaluation
Measured value block 13 -evaluation
CBJBdiesel engine (pump injection)
Description of the drive
CBJB technical data
Checking the coolant temperature sensor 0B1
Checking the engine speed sensor 0B2
Removing and installing the engine speed sensor 0B2
Actual speed sensor 1B1
Checking the hall-effect sensor 0B8
Checking the fuel temperature sensor 0B3
Checking suction pipe temperature sensor 0B4
Checking the suction pipe pressure sensor 0B4
Glow plug system
Ceramic glow plugs 0R4
Fuel supply
Rules for working on the direct fuel injection system
Checking the tandem pump delivery pressure
Removing and installing the tandem pump
Pump injection unit- overview
Pump/nozzle unit -Checking valves 0Y2
Removing and installing the pump injection unit
Changing the O-rings and thermal protection seal on the pump injection unit ..
Engine block
Cylinder block -overview
V-ribbed belt- removal and fitting
Removing and installing the free-wheel belt pulley
Toothed belt -removal and fitting, tensioning
Changing the crankshaft sealing ring on the toothed belt pulley side
Removing and installing the crankshaft sealing flange
Cylinder head -overview
Cylinder head cover- removal and installation
Removing and installing the cylinder head
Cylinder head -checking the compression pressure
Valve train - overview
Valve stem covers- removal and installation
Checking the camshaft for axial play
Removing and installing the camshaft sealing ring
Removing and installing the camshaft
Oil filter and oil cooler -overview
Removing and installing the oil sump
Suction pipe -overview
Checking the suction pipe flap switchover
Suction pipe flap -Checking switch valve 0Y16
Vacuum hoses -connection diagram
Air volumeter 0B6
Checking the charge pressure limitation solenoid valve 0Y4
Exhaust gas recirculation
Exhaust gas recirculation -overview
Checking exhaust gas recirculation
Checking the exhaust gas recirculation valve 0Y3
Checking the mechanical exhaust gas recirculation valve
Checking the cooling system for leaks
Draining and filling coolant
Removing and installing the coolant thermostat
Removing and installing the coolant pump
Self-diagnostics - introduction
Error code table
Standardised measured value blocks
Measured value block 01 -fuel injection quantity
Measured value block 03 -exhaust gas recirculation
Measured value block 04 -pump/nozzle unit activation
Measured value block 07 -temperatures
Measured value block 10 -air variables
Measured value block 11 -charge pressure control
Measured value block 12 - heating status
Measured value block 13 - idling smooth running control
Measured value block 18 valve status of the pump/nozzle unit
Measured value block 23 - BIP deviation (solenoid valve switching times)
File Data

This file is sold by tbit, an independent seller on Tradebit.

File Size 1 megabytes
File Type PDF
Our Reviews
© Tradebit 2004-2021
All files are property of their respective owners
Questions about this file? Contact tbit
DMCA/Copyright or marketplace issues? Contact Tradebit